Storefront Door Locks in Hayward
Glass doors on B Street and Mission Boulevard: hookbolts that will not throw, worn deadlatches, tired cylinders, closers that slam. $145 to $429.
$145–$429
Typical price
24 min
Avg. arrival
24/7
Availability

Walk B Street, then Mission Boulevard, then the frontage around Southland, and the shop doors are nearly all one door: a sheet of glass in a slim aluminum frame with a lock buried in a stile about two inches wide. That door is a trade of its own, and the parts for it do not live in a hardware aisle. Eden Locksmith carries them on the van: deadlatches, hookbolt deadlocks, mortise cylinders with the correct cam and tailpiece, paddle handles, inside thumbturns and the closer at the head. A bakery, a barbershop, a taqueria, a nail salon, a pharmacy near the mall. What all of them want is a door that locks the way the lease says it has to.
The first thing done at a storefront door is to close it and watch where the latch lands. Most of the time the lock is fine and the door has dropped. Aluminum doors hang on two pivots, the bottom one wears, and after a few years the deadlatch is arriving three or four millimeters below its pocket, which is why the door opens when you pull on it after locking. A new pivot and a moved strike cure that for a fraction of a new lock, and that is what gets quoted when that is what is wrong. When the deadlatch really has worn short of full throw, a new one goes in. Hookbolts go on doors that meet at a center mullion or that have been pried once already, because the hook wraps the strike and cannot be spread out of it. The mortise cylinder is repinned or replaced with one carrying the right cam, and a thumbturn goes inside so whoever closes can lock up from the shop floor instead of standing on the sidewalk at eleven at night.
Storefront work is $145 to $429 per door with hardware, the $89 service call counted in. A deadlatch swap or a new mortise cylinder is the $145 end. A hookbolt deadlock on a restricted cylinder with a paddle handle and the closer reset on a heavy door reaches $429. Repinning a stile cylinder when somebody leaves the payroll is $24 to $39. Evening work after 8pm carries $45 inside the figure and work before 7am carries $80, both said on the call.
You call and say what happened, with a photograph of the door edge and one of the lock face. The figure is said on the call. The van leaves Jackson Street, and a text names the technician and gives a thirty-minute window; B Street and Mission are both inside twenty-four minutes, and morning slots before opening are the ones most shops take. The door is checked for droop, repaired or refitted, keyed, then swung through the closer a dozen times. The receipt shows the figure from the call and names the make and model of every part, in case the landlord asks what went into their door.
“The aluminum front door of my restaurant on B Street had a hookbolt that only threw if you pulled the door toward you, and the closer was slamming it hard enough to rattle the glass. $325 for a hookbolt, a cylinder and the closer set properly. Seven in the morning, before prep, and he squared the door so the bolt lands clean instead of scraping. The place I used before this told me the frame was finished and wanted to sell me a whole door. $325 on the card and $325 on the receipt.”
Every job is priced from the list below. The figure is said while you are still on the phone, and the receipt shows the same figure whatever the technician finds at the door.
- Daytime (7am–8pm)standard rates
- Evening (8pm–12am)+$45
- Overnight (12am–7am)+$80
FAQ
Storefront Door Locks: quick answers
I lock the shop, pull the handle, and the door opens anyway. Is the lock finished?+
Probably not. Stand inside and watch the latch as the door swings shut. If it lands below the pocket in the strike, the bottom pivot has worn and the door has dropped, which is a pivot and a strike adjustment rather than a lock. If the latch reaches the pocket and then slips out under a pull, the deadlatch itself has worn short and gets replaced. Either job is a routine call and it is done before you open.
There is a roll-down grille in front of our door. Can the grille and the door run on one key?+
Usually. If both cylinders share a keyway they are pinned to a single key at the van. If they do not, the grille cylinder is replaced with one that matches the door, and that comes to a line of its own on the quote. Copies get cut for everyone on the opening list, and both cylinders are named on the receipt.
An employee left and did not hand back the key to the shop.+
Ten minutes at the door. The stile cylinder comes out, gets repinned at the van for $24 to $39 and goes back in, and the key on that ring stops turning. Fresh keys are cut for everyone still on the closing list. Nothing else on the door is touched, so the closer, the handle and the alignment stay exactly as they were.
Related
More commercial services
24/7 — nights, weekends & holidays
The van is already in town, and the number comes before it moves
Hayward, San Lorenzo, Cherryland and Ashland, San Leandro, Castro Valley and Union City, 24/7, holidays included. Describe the door, hear one number with the $89 visit inside it, and the lock gets opened without damage wherever it can be. The receipt says what the call said. It runs the same way whether the lease is in your name or the deed is.